Mega Rad Gun Thread

[SHIGGSHOGG]

Printer bois gonna fuck atfs shit up if this happens........ the short MP22 uses about 20g of filament, so at $10/kg that's 50 per roll at ¢20 per piece
Also soda bottles with rags lmao, I hear those hold up for a while with .22 and only cost you ¢5-15 depending on what your state taxes you for redemption fee

 

[God's drunkest driver]

Regarding weapon acquisition, is there anything that makes you all stop concerning yourself with getting [next thing]?

I view any gun that isn't an oddity, a classic, or different in that it fills a niche very well, as just a tool, I simply don't care about new stuff.

Helps that I find most modern guns fugly and since guns aren't computers or cars, their performance isn't light years away from where they were in 1990 and the modern configs are usually only marginally better than the stuff I already have. The only modern weapon configuration that I had any significant interest in was the micro-9s, and they aren't that modern, just popular now. The first P365/Hellcat sized double stack 9 was produced by the intrepid minds of Lel-Kek almost 30 years ago and I there's the G26 which is a micro 9, just fat. What am I going to do? Replace an already very good AR10 with a SCAR? They're a lighter but look like total shit and cost an arm and a leg. Replace an old Sig or classic range toy with a 2011? 90% of them look like mallninja edgelord gunkata movie crap. Replace an old Howa based precision rifle build with something new and twice the price? For what? In the end, you can't replace what's great about the classics with the next thing, and the next thing isn't a massive upgrade over the "tool" grade firearms I already have, so I simply don't gunsoom.

 

[Pretend To Imagine]

Regarding weapon acquisition, is there anything that makes you all stop concerning yourself with getting [next thing]

Guns are completely soulless tools to me. I have a truck full of tools that serve a purpose for my work and I treat guns the same way, they are means to an end to put bullets where I want them to go.

If I had fuck you money, I would have a YouTube channel where I buy collectible, rare transferable machine guns and destroy them on camera just to make faggot collectors cry

 

[Internet-Based Lobotomy]

If I had fuck you money, I would buy collectible, rare transferable machine guns

Me too.

Printer bois gonna fuck atfs shit up if this happens........ the short MP22 uses about 20g of filament, so at $10/kg that's 50 per roll at ¢20 per piece
Also soda bottles with rags lmao, I hear those hold up for a while with .22 and only cost you ¢5-15 depending on what your state taxes you for redemption fee

.22 is stupidly easy to make quiet. The bottle and rags and cheap ass plastic printed suppressors will probably become super common. $0 NFA or not. I mean hell we all know the most recent negative mention of suppressors was because of Luigi and IIRC his was some printed bullshit. Was it the FTN? Those were a bit more "Gucci" and required more effort but they were smaller than most 9mm printed cans that are like 4" in diameter and a foot long.

 

[POWER IN MISERY]

anyone know how i can get my bobcat's slide to stop popping up when i tip up the barrel with a loaded magazine?

 

[Internorth Inc]

If I had fuck you money, I would have a YouTube channel where I buy collectible, rare transferable machine guns and destroy them on camera just to make faggot collectors cry

Considering a decent amount of those collectors are Boomers with a "Fuck you, got mine" mindset, they'll probably be elated that their "investments" have gone up in value.

 

[Pretend To Imagine]

Considering a decent amount of those collectors are Boomers with a "Fuck you, got mine" mindset, they'll probably be elated that their "investments" have gone up in value.

They will be dead soon and their family will probably turn the guns in at a “ buyback”

 

[DocAwe]

$20 oil filter adapters for everyone.

 

[Taser Confetti]

Now if only they weren't NFA items and any machine shop could just start cranking these things out...

We're talking about a cylinder with threads and baffles, people have diy'd these things at home. Also the bigger picture is that any company could subcontract out parts and they'd have controls in place for QA. For example it wouldn't be 18 different competing shops popping up (at least not completely) but it'd be a shop with tooling getting an order from some silencer company to make them 1000 bodies on their CNC machines and another company would get orders for baffle stacks or whatever etc. You can scale up parts of the whole, it's not suddenly a garage workshop popping up out of nowhere with $600 total in hand tools making these things. It'll be a machine shop that preferably fabricates parts within tight tolerances getting another set of products to run. I think a tried and true machine/tool shop that didn't have to get yet another certificate and more government bullshit to deal with would be more than happy to stick their toe into said market, even if it is just throwing one different part into their wire EDM machines.

Listen if you're happy Vietnam era technology I'm sure it'll be fine - I don't trust a subcontractor to make a proper flow through supressor.

 

[Legato]

If you want a suppressor just buy one. The wait time is practically zero and there are plenty of cheap options by reputable companies.

They are not going to get cheaper any time soon.

 

[Club Sandwich]

anyone know how i can get my bobcat's slide to stop popping up when i tip up the barrel with a loaded magazine?

the slide is retained by two "wings" at the rear of the frame. ensure that the slide isn't out of position when you tip the barrel, as the magazine pressure will push up the top round into the bottom of the slide and this can move the slide forward slightly allowing it to move out of position. inspect the wings - they should be angled on the underside but square at the front and rear.

 

[VF-1S Valkyrie]

I do not like the tang safety. Button safety supremacist.

If you're going to use a pistol grip, button all the way. For traditional stocks, tang is just as good, if not better in some minor ways.

 

[POWER IN MISERY]

the slide is retained by two "wings" at the rear of the frame. ensure that the slide isn't out of position when you tip the barrel, as the magazine pressure will push up the top round into the bottom of the slide and this can move the slide forward slightly allowing it to move out of position. inspect the wings - they should be angled on the underside but square at the front and rear.

if i have the hammer cocked back and pull the trigger when the safety is engaged the hammer will fall the moment i disengage the safety. should i hound beretta?

edit to avoid double posting;
i'd ask how ukranian gypsies aren't fucking embarrassed of this blowback bullshit if there were more than like four thousand of them left

 

[SuperConglomerateWhale]

I for one am not dropping hundreds of dollars on an item a company started manufacturing last week.

Saar Saar please buy törkish shottygun made of my ditch feces Saar

Get a Mossberg

I think the Benelli Supernova is better for quality reasons. The last few new 500’s and 590’s I’ve seen had shit manufacturing finishes. I still love my A300. Thing is a niggerchopper.

 

[Taser Confetti]

If you want a suppressor just buy one. The wait time is practically zero

Next couple of days the system is gonna get flooded so act now or give it a year or two.

 

[BikeLock]

Printer bois gonna fuck atfs shit up if this happens........ the short MP22 uses about 20g of filament, so at $10/kg that's 50 per roll at ¢20 per piece
Also soda bottles with rags lmao, I hear those hold up for a while with .22 and only cost you ¢5-15 depending on what your state taxes you for redemption fee

An empty 1 liter soda bottle packed full of 000 steel wool works much better than one would expect, even just electrical taped on the end of a .22 rifle.

In Minecraft, of course.

 

[Rainbow Idiot]

I'm filing for so many .22 printed cans myself.

 

[Internet-Based Lobotomy]

Listen if you're happy Vietnam era technology I'm sure it'll be fine - I don't trust a subcontractor to make a proper flow through supressor.

With all the 3D printed designs now they just have to have properly calibrated machines. Seeing as how availability and tooling costs are the biggest limiter to supply this would be a good thing or one would think. Not like every single component is made in house at all of these places anyways, there are SOT certified subcontractors after all. Unless you think there's something else that's an impossible task for specifically flow through suppressors?

Saar Saar please buy törkish shottygun made of my ditch feces Saar

If the NFA was axed I think for most people a Turkroach and Chinkoid clone of a good suppressor at half the cost and in aluminium instead of titanium would elicit few complaints. "Works for muh use case."

An empty 1 liter soda bottle packed full of 000 steel wool works much better than one would expect, even just electrical taped on the end of a .22 rifle.

In Minecraft, of course.

Or in real life if you pay your $0 tax stamp.

 

[Bassomatic]

So much politics nonsense. Ugh. Well, so I think a lot of you know me when I pop in. But local smith who was the guy who built (more like unfucked) my Bren and is a super guy is offering an AR night... I built a few (all of them aside my LaRue) I hate to sound full of myself but it's not hard... thing is with law changes and I'm going to swap my LaRue to a piston upper because it's SBR stamped now and I have a can.... maybe I can learn? I mean making a PSA build I can do blind folded.. but if he's offering this class I think's above it.

What do you all say? Esp, His Sandwich self.

Also in good news 300 more rounds of my 9x18. I just re did the red for hot.. I'll upload a picture next free second. Hope you're all well gun frenz.

Also Hunters Lodge has FR8s... I'm legit wanting a second, if you don't own an FR8 no matter what youre into for guns.. get one. They kick ass.

 

[AGPinochet]

I am unsure if the stipulation was retained in the current version of the bill but from what I read previously the $0 stamp doesn't go into effect instantly, but instead it goes into effect 90 days after the end of the current fiscal quarter.
Which If I am not retarded means January 2026.
Now this stipulation (if retained in the current version of the bill) could cause a few things to happen

1. People panic buy suppressors in an effort to get ahead of what I will describe in point #3
2. Manufacturers will be given 5 months to buy as much raw material, machines and tools, hire as much staff (for 2nd and maybe even 3rd shifts) and stockpile as much inventory as possible in order to prepare for
3.Formageddon
What is "Formageddon"? Formageddon is a hypothesized event that I literally just made up that is theoretically forecasted to begin as early as Midnight on New Year's eve 2025. It's start date cannot be accurately pinpointed because it is dependant on how lazy the ATF is on preparing the E-forms system for a deluge tens if not hundreds of thousands of Form 1's and 4's (and whether or not the fiscal quarter language has been retained in the bill), stress on the system could be further exacerbated by every Silencershop Kiosk in the country being besieged on New Years Day. Formageddon could realistically last until February or March of 2026. Think of it, how many Suppressor virgins are tucking away cash for that OCL, Surefire or CAT they're eyeing? Thousands, tens of thousands, A few months from now, maybe even hundreds of thousands

Every suppressor company is going to post their best month, no, quarter ever