Mega Rad Gun Thread

  • Want to keep track of this thread?
    Accounts can bookmark posts, watch threads for updates, and jump back to where you stopped reading.
    Create account
Screenshot_20250110-141350.png


Can't find much else about this. Taking it with a grain of salt . Orgs like to whip up fear
 
Last edited:
On the topic of the RXM, I think it's very compelling at least conceptually. For what it's worth Gun Talk Media ran over 8,500 rounds over two days, with Glock factory and MagPul magazines, through their copy without stoppages or parts breakages. It shouldn't have parts breakages at that round count, but it's good to see the lack of stoppages. They don't show the full firing of the gun from start to finish, so they could have faked their results, but I'm going to choose to believe them.

I've read about a couple issues that some users and reviewers have with reliability due to either their screws for their optic being too long or over torquing screws in their optic inducing malfunctions. You will impede on a spring that is visible through the drilled out screw hole. This is possible and somewhat common to happen with a factory slide that you have milled. It's also an issue with optics cut P80 builds/other clones. Not exactly an inherent fault with the gun.

I've seen reports of the slide stop causing issues, the ejector being out of spec, and the same complaints echoed above about the magazine issues. What's real or user induced will come out in time. About half the complaints I've seen have been user induced from guntubers and a good amount of real issues seem to be fixed by swapping a part for a new Glock OEM part. I'd echo again what was said above, don't buy the first gen, Ruger will iron out the problems eventually. Lots of shilling by guntubers though, hard to find higher round counts and clear videos of why stoppages occur.
 
The ATF can lick the whole entire inside of the anal cavity of an AIDS infected male prostitute. Seriously, fuck the ATF up the ass with a running chainsaw.
 
So from my rudimentary understanding of gubmint legal words, the ATF is repeating that their interpretation of a stabilizing brace is that it is a stock. However, they are not prosecuting due to the Court's decision during the appeal process. They then reiterate that adding anything with the intent to shoulder a pistol is bad, which coincidentally includes intent(specifically) in regards to braces which they imply they can and will prosecute.

Nothing has changed, grifters are grifting. The bottom of the coffers are visible so they must collect.
 
Matador Arms is releasing some interesting things at SHOT
They said this frame ISN'T for an RXM FCU and I believe them (there wouldn't be a matching cutout on the left side if it was)
1736608622783.png

They're also bullpupping their proprietary bufferless upper
1736608696217.png

They're also doing a collaboration with Stuff and Things and their Bizon mag copies
Some guy made a fucked up PCC with a weird mag, it's called the Speed 9, it has two opposite facing cartridge stacks but only feeds from the forward facing stack, idea is that you fire off a mag's worth, eject the mag, flip it around and then fire the now forward facing stack off. Expect to see it on Forgotten Weapons in 15 years. According to a literal who random nobody on /k/ this guy is partnered with a "Major Pistol manufacturer" (which to me sounds like Zev or Shadow Systems but Zev is owned by Silencerco now so I don't know how that would affect the probability)
1736608974828.png
Here's the website with a bunch more photos and some videos

Proprietary everything, the only way this thing is cool is if it can function with an FRT

You ever want to convert your 3D Printed AK into a 3D Printed Bullpup AK. Soon you can with this WIP Bullpup conversion of Plastikov V4 3D printed AK receivers
1736609171073.png

Another image of the circular version of the MACV-SOG "Death Machine" ammo pack
1736609497220.png
I recently learned that the conceptual origin of these types of packs (at least for M-60's, I don't know when the semi famous prototypes for AR-10's were made) was the Army's Limited Warfare Laboratory (LWL). This one isn't in use with a SOG RT Man from what I can tell, probably in the process of stateside testing
1736609587785.png

"UGH, my ACRO is so BULKY"
1736609852350.png

HK SL-7 with 20rnd mag
1736609887894.png

Bullpup M14 conversion
1736609944761.png

1736609960632.png
In the flesh
1736610032330.png

I personally would pick a mounting system other than Keymo for my revolver suppressor host
1736610105825.png

The Atlas Engineering MBAR prototype now has initial 7.62 AK mag compatibility
1736610235538.png

Some guy(s?) managed to somehow import like 50 Bizon parts kits without getting that shit seized by customs and are SLS Printing mags for them
1736610694124.png

Below is a screenshot of an Arfcom post by Bill Geissele talking about the release of Federal's new 7mm Backcountry (incorporates a Steel/Boron Alloy case to allow for higher pressures) and Geissele's new bolt gun. He says that there are more high pressure cartridges coming down the pipe
1736610867213.png

Custom PB
1736611271521.png

1736611296319.png

Zenitco Type 3 AK, rare to see anything before an AKM equipped as such
1736611409740.png

Canadian Police seized a "Not a Glock" .22 pistol in December, gun was released in October.
1736611523986.png

Glawk and 7N21 (look at the mag). This is supposedly, allegedly, maybe, the personal carry loadout of Jewish Midget, Helicopter pilot and occasional guntuber, Oxide.
1736611697210.png
 
Syrian terrorist with a 9A-91, a couple dozen/hundred of them were looted from the Syrian Presidential Palace and probably other internal security and special forces facilities so expect to see them floating around the ME for the next couple decades, even just as collectors items like Syrian STG's are now ever since all the ammo got shot up
1736612136771.png

hard to see but at the top there's an integrally suppressed SKS
1736612502796.png

.22 Lifecard, but it's the funny one name movie man
1736612547318.png

Back in the 80's there was a brief moment were Federal tried to make a rimmed 9mm cartridge for revolvers but then they realized that was dumb and that revolvers are obsolete so then they stopped. Called 9mm Federal
1736612714075.png

M1 carbine with XM148 UBGL
1736613078368.png

Incredibly crude Idlibi RPK conversion
1736613266374.png

Three Iraqi SKS's
1736613426112.png
1736613445527.png
1736614118599.png

Another Iraqi got ahold of a 1917 Enfield and did this to it. Note that it has both a Warsaw pact side mount a pic rial scope base
1736613602801.png

Tactical RPD with lightening cuts
1736613717266.png

Inspired by an SVD
1736613821953.png

Custom Iraqi SMLE
1736614090616.png
Another one, this one comes with a fake gas system
1736614194318.png

VZ.48 with a bike handle foregrip
1736614585819.png

1736614607190.png

1736614625755.png

AKM converted to 5.56 with the aid of an M16 barrel and Zastava mags
1736614672596.png

fat Ayrab Brandon Herrera with a fishgun
1736614884081.png

Georgian "TAO" Smg
1736614980741.png
 
AGPinochet said:
They said this frame ISN'T for an RXM FCU and I believe them (there wouldn't be a matching cutout on the left side if it was)
Click to expand...
The FCU shit is so annoying because nobody ever does anything or if they do they stop making them/it turns into vaporware. At least with the Magpul x Ruger crossover you still have Magpul and their mad scientists.
 
You must log in or register to reply here.
Back
Top Bottom